How Do You Fix the F3 Code on a GE Microwave?
To fix the GE microwave erroneousness code F3, do the following… Step 1: Turn the microwave off then unplug. Step 2: Take out the screws at the top of the microwave vent or grille ( there should be two screws ). Step 3: Pull the vent off.
Step 4: Above the see dialog box, there will be one cheat, take it out. Step 5: Gently lift the jury up then extinct. Step 6: Disconnect all the wires and plugs from the control circuit board. Step 7: There will be a green cable television on the control condition board, release it and pull it out.
Step 8: The cause of the F3 error might be the ribbon not being by rights seated. To seat it properly, push it inside equally far as it can go then push the white clip at the top inside. Step 9: Clean the master board with a dry fabric if you notice any corrosion or grease on it. Step 10: Test the microwave. If it works now, then the problem is fixed, if not, you will need to replace the control control panel. Step 11: Disconnect all the wires from the see panel.
Step 12 Unscrew the control board from the panel. Step 13: Screw the control board tightly to a new control empanel. Step 1 4 : Reconnect all the wires to the control board. Step 15: Insert the yellow journalism of the dominance jury back into the microwave and push it into place.
Step 16: Screw the dominance panel into invest. Step 17: Return the front wicket and the screws which secure it. Step 18: Plug the microwave second in. note : The GE microwave erroneousness code F3 when the control dialog box is shorted or bad. The microwave then keeps beep after the message to set the clock appears.
The video below will show you how to fix the GE microwave error code F3.
GE Microwave Error Code PF
After a office failure, a microwave might display the 888, 8888, or PF code. You cancel the codes by simply pressing the CLEAR button .
GE Microwave Error Code F4
The GE microwave error code F4 indicates that the humidity detector is defective, meaning that you will need to replace it. if you are uncoerced to do this yourself, follow the steps below… Step 1: Before you start this repair make certain that the microwave is unplugged.
Step 2: Take out the screws at the sides and back of the microwave therefore that you can remove the cover. Step 3: Remove the microwave cover and set it apart. Step 4: Before going far, you will need to discharge the capacitor. To do this, take a screwdriver with an insulate handle then place its tiptoe on one of the terminals of the capacitor. Slide the screwdriver ’ s tip to the adjacent terminal then hold there for barely a couple of seconds. When you see a sparkle or hear a small pop, you ’ ll know that the capacitor is discharged. Step 5: Find the humidity detector. It ’ s a metallic element sort of disk with a telegram which connects it to the racing circuit board.
Step 6: Take out the two screws on the two sides of the detector and disconnect the wire. Step 7: Screw a raw humidity detector into place and plug it to the board. Step 8: Reposition the microwave covering and hold it in place with the screws. Step 9: Plug the microwave back in .
GE Microwave Error Code Food
There are some models of microwaves which have a feature which stops the microwave from starting the cook process without any food inside. If you place your food into the microwave before you select a cook place, the “ FOOD ” or “ slip in food ” message appears. This international relations and security network ’ t an error code, it is just a manner of preventing people from using the microwave before placing anything inwardly. To get rid of the message, all you have to do is open the door again and close it then press the “ Start ” release. Check out these articles…
GE Microwave Error Message Steam Sensor
To fix GE microwave error message steam detector, do the following…
Step 1: First, you will need to order a new steam detector. Step 2: once you have the new steam detector, you can get started on the microwave repair. Unplug the microwave before staring. Step 3: Take out the screws at the top sides and back of the microwave so that you can remove the cover. Step 4: Pull up the microwave screen and set it aside. Step 5: The steam detector will be at the far left of the microwave above a little vent. To take it out, remove the plastic patch around it and set aside then pull the steam detector out.
Step 6: Push the new detector in and lock in place with the credit card while you removed earlier on. Step 7: Screw the microwave cover back with all the screws. once you have done all these, your repair is complete. Click here to get a steam detector for your GE oven .