Does microwaving a die significantly alter its balance?

\ $ \begingroup\ $

It doesn’t do anything.

As a chemist, I had to give this a attempt .
first, I started with a die that had a clear bias toward ~18, according to the seawater screen. The first movie is the initial drop into the water, and the second is after poking the die .
enter image description here

I put the die on a composition denture, and microwaved it for 4 minutes. I made sure to put it on its “ side, ” so that if there was some kind of difference on the top and bottom, it would affect the balance .
enter image description here
After microwaving, I put it back into the strategic arms limitation talks water, to see that there is still a pugnacious bias toward 18. As ahead, the left is pre-poke, and the right is post-poke .
enter image description here

This is not surprising.

I could have microwaved it even more, but I do n’t think that it ‘s necessity : while the newspaper plate got hot, the die hardly warmed up at all .
This is because microwaves work through insulator heat, which requires the molecules to have a dipole moment. Dice are made of polymers, and while I do n’t know precisely which polymer my die is made of, many polymers do n’t have a permanent dipole moment and frankincense would n’t warm up importantly in the microwave. I suppose you could microwave for a very long time, or submerge it in something that does heat up, but that ‘s an amazing batch of campaign for a one laden die .
If you want to melt your dice, you ‘re better off putting them in the oven. If you want load cube, you should precisely buy one .
I do n’t even think that melting your cube would affect their balance anyhow. Most things, including microwaves, heat from the away in. In the case of, say, a hot scoop, the interior heats up a draw faster because it has a fortune more water to get heated, compared to the relatively dry pastry outside. however, gaming dice are pretty a lot uniform throughout, and so any dissolve that could credibly affect the home balance would mean that the outside would be obviously melted .

What if we put it in something that does heat up?

In true Mythbusters manner ( and because this answer is getting a set of attention ), I wanted to see if there was a means to get the microwave to affect the die. We know that water heats up a lot in the microwave, so what if we put the die partially in a layer of water, so that one english of it get heated and the other does n’t ?
I put the same fail rear in the newspaper plate, and added a level of water to submerge half of the die. I then put it back in the microwave for 4 minutes, and measurement the temperature of the urine. As you can see, the water decidedly heats up ( it was actually at boiling when I first measured it, and cooled slightly before I took the word picture ) :

enter image description here
212 F is the hottest that liquid water can get. Any supernumerary energy that goes into non-superheated water system at 212F will go toward evaporating the urine, not increasing its temperature. Therefore, 212F is the utmost temperature we can apply to the die with this frame-up .
After the die was partially boiled, I noticed that the surface that was under the water had a slightly chalkier texture. Is this heat adequate to affect the proportion of the die ?
enter image description here
unfortunately, no — the die placid shows a bias toward 18 .

What about the oven?

This is a bit outside the setting of the interview, but I was curious to see if the higher temperature of the oven would be able to change the poise of the die without obviously changing its appearance. I preheated the oven to 300F, and put the poor d20 inside for 20 minutes :
enter image description here
This melted the penetrate of the die :
enter image description here
Which was enough to significantly change the balance in the seawater test :

enter image description here
So yes, the basic principle of melting your die to change its balance works. however, you need to melt the die in the higher hotness of the oven, and not the microwave. It besides obviously changes the appearance of the die, so you ‘re not going to make any secretly loaded cube this way .
fair buy a loaded d20 .